Home / Guides / PC cooling

AIO Pump Header: CPU_FAN or AIO_PUMP?

Find the right header for your AIO by separating pump power, speed reporting and fan control. Includes examples from NZXT and ARCTIC wiring guides.

US Liquid Cooling editorial · Reviewed · 4 min read

An AIO pump does not automatically belong on a header called AIO_PUMP. The correct connection depends on whether the cable supplies pump power, controls speed, or only reports a tachometer signal. It also depends on where the radiator fans connect.

Read the cooler wiring diagram and the motherboard header ratings together. The name printed next to the socket is only the beginning of the answer.

Identify the job of every cable

Make a small connection map before plugging anything in:

Cable functionQuestion to answer
Pump powerDoes power come from the motherboard, a PSU lead or a proprietary hub?
Pump speed signalWhich connector sends RPM back to the board?
Fan power and controlAre radiator fans on the board, the cooler or a separate controller?
USB communicationIs it needed for monitoring, configuration or a display?
LightingIs it a separate lighting connection, unrelated to motor power?

This avoids a common mistake: assuming that an illuminated pump cover proves the motor has the power and control settings it requires.

A power cable and a tachometer cable can look similar

NZXT's pump-header explanation distinguishes header-powered products such as Kraken Core from models that take separate PSU power and use a motherboard lead to report pump speed.

For a header-powered pump, changing the header's output can affect the pump itself. For a tachometer-only lead, changing that header's fan curve may have no effect on actual pump speed. A monitoring cable cannot replace the required power connection.

That distinction is why two otherwise reasonable installation guides may give different instructions. They may describe different electrical arrangements, not disagree about the same cooler.

What should connect to CPU_FAN?

Many motherboards monitor CPU_FAN for an expected speed signal and display a warning when it is missing. Depending on the supported wiring arrangement, that signal may come from the radiator fans or the cooler's pump-sense lead.

Do not immediately disable the warning to make a new build boot quietly. First confirm which device the motherboard is supposed to monitor. If an approved setup requires a monitoring adjustment, document it and keep a meaningful way to detect loss of cooling.

Use the exact motherboard manual for header current limits and supported control modes. CPU_OPT, W_PUMP and AIO_PUMP are not standardized promises about available current or behavior on every board.

Does every pump need to run at 100%?

No. Some models require fixed full-power operation; others support adjustable pump control. For example, NZXT states that Kraken Core's header-powered pump should receive full-speed output. That does not create a universal prescription for all AIO pumps.

ARCTIC's Liquid Freezer III manual illustrates a different arrangement: users can choose a shared control cable or individual control for the pump, VRM fan and radiator fans. The cable selected changes how the assembly is managed.

Match DC or PWM mode to the manufacturer's instructions. Do not assume pin count alone tells you everything when splitters, combined cables or proprietary electronics are involved. Avoid a fan-stop profile on a pump unless that exact behavior is explicitly supported.

Can a fan hub power the pump?

Only if the hub and pump documentation explicitly support that connection, including electrical load and startup behavior. A connector fitting physically is not sufficient evidence. Lighting controllers are a separate issue and should never be treated as interchangeable with motor-power outputs.

The Kraken Core manual, for example, documents a fixed-speed pump arrangement. Use it for that product, not as the wiring diagram for another Kraken generation.

Check the installation in three stages

With the machine off, verify cable destinations and secure connections. At the first controlled startup, confirm that the intended speed signals appear and that the CPU temperature behaves normally. After installing the supported software, check which controller actually owns each fan or pump setting.

Keep a note such as: “Pump powered by PSU; pump tachometer on CPU_FAN; radiator fans on cooler controller.” If troubleshooting becomes necessary later, that single sentence prevents a lot of guesswork.

If RPM appears normal but cooling fails, investigate overheating with a running pump. If temperatures are stable and sound is the problem, use the separate pump-noise checklist.

Sources & further reading

Use the manufacturer’s instructions for your exact equipment. Read our editorial policy or suggest a factual correction.

Explore the company directory → · All liquid-cooling guides →

01
PC cooling

AIO Pump Running but CPU Overheating? What to Check

Check mounting, wiring, radiator airflow and circulation when your AIO reports pump RPM but the CPU still overheats. Includes a troubleshooting table.

↗
02
PC cooling

AIO Pump Noise: Gurgling, Rattling and What to Check

Identify AIO bubbling, rattling and vibration, check radiator orientation, and learn when to contact support. Includes safe troubleshooting steps.

↗
03
PC cooling

Water-Cooling Fan Curves: CPU or Coolant Temperature?

Build a radiator fan curve using coolant readings, room conditions and component limits. Covers sensor choice, pump settings and fallback behavior.

↗

Directory matches are starting points for research. Confirm product fit and availability with the company.