US Liquid Cooling editorial · Reviewed · 4 min read
Use the glycol concentration approved for the chiller, fluid product and lowest relevant operating condition. More glycol is not automatically better: concentration affects freeze protection, viscosity, heat capacity and the inhibitor package.
Start by defining what needs protection. A system that must circulate fluid in winter has a different requirement from an idle circuit that only needs protection against freeze-related damage.
Freeze protection and burst protection are different
Freeze protection aims to keep the solution from forming ice at the specified condition. Burst protection concerns damage from freezing and expansion; it does not establish that the fluid remains suitable for normal circulation.
The ASHRAE secondary-coolant chapter explains that the required concentration depends on the type of protection. Do not select a burst-protection number for an operating circuit that needs pumpable liquid.
Include the coldest credible condition at the relevant location: normal operation, outdoor exposure, shutdown or storage as specified by the equipment suppliers. “The room is usually warm” is not a complete design condition for a circuit that extends outdoors.
Why can excess glycol reduce cooling performance?
Compared with a water-based selection at lower glycol concentration, a more concentrated mixture can have less favorable heat-transfer properties and higher viscosity. The effect depends on the chemistry and temperature.
Dow's data-center cooling explanation specifically notes the pumping consequences of rising glycol concentration. Its DOWFROST product information also distinguishes product composition and protection capabilities.
Evaluate the actual product's property tables and the chiller's rating conditions. A unit rated with one fluid mix may need a different selection when the concentration or operating temperature changes.
Check the product percentage, not just “glycol”
An inhibited concentrate is a formulated product. It may not be 100% glycol, and its minimum approved dilution can reflect the concentration of corrosion inhibitors as well as freeze protection.
Clarify whether a chart means percent by mass, percent by volume, or percent of a named concentrate. Those are not interchangeable. “Thirty percent glycol” without that definition is an incomplete instruction.
Keep the fluid manufacturer's requirement and the chiller manufacturer's requirement together. If they cannot be reconciled, resolve the selection before filling rather than choosing a compromise percentage in the middle.
Residual rinse water changes the final mixture
Account for fluid already inside the system. In a simplified volume-based arithmetic example, 30 L of a 40% mixture combined with 10 L of water gives approximately 40 L at 30%, assuming additive volumes. This demonstrates dilution; it is not a mixing recipe for a named coolant.
The same issue arises when topping up repeatedly with plain water or transferring fluid between systems. Record the product and quantity of each addition rather than treating the reservoir label as permanent evidence of concentration.
Where accurate final concentration matters, follow the specified mixing and measurement method rather than relying only on quantities poured into a partially drained circuit.
How should concentration be checked?
Use an instrument and calibration appropriate to the exact fluid. A refractometer needs the correct scale or conversion; a reading from an unrelated fluid scale is not a valid result. Follow the supplier's temperature compensation and sampling instructions.
A concentration measurement also does not establish inhibitor condition, contamination or complete fluid health. Those may need separate checks or laboratory analysis.
For a process-fluid review, record:
| Question | What the record should contain |
|---|---|
| What is installed? | Manufacturer, product grade and batch |
| What was the target? | Approved percentage definition and reason |
| What was measured? | Method, instrument, sample point and result |
| What has changed? | Top-ups, repairs, dilution and operating conditions |
| What else is required? | Chemistry and condition checks specified by the suppliers |
Which glycol should a process use?
Choose the fluid family and formulation for the equipment, materials and application. A beverage-related cooling system has different product requirements from an industrial circuit. An automotive antifreeze bottle is not a generic substitute for an approved process fluid.
Read the technical and safety data sheets together. For fermentation applications, our glycol chiller sizing guide explains why the mixture, temperature and duty must be evaluated as one system.
Sources & further reading
- CHAPTER 31. PHYSICAL PROPERTIES OF SECONDARY COOLANTS (BRINES) ↗
- Cooling Solutions for Data Center & Cloud Performance | Dow Inc. ↗
- DOWFROST™ Heat Transfer Fluid | Dow Inc. ↗
Explore the company directory → · All liquid-cooling guides →